In reply to Prawin kumar:
Why are you creating a driver and monitor (and sequencer?) in your environment? You are creating an agent which should contain these components. In your environment, you should only create the agent and scoreboard.
In reply to Prawin kumar:
Why are you creating a driver and monitor (and sequencer?) in your environment? You are creating an agent which should contain these components. In your environment, you should only create the agent and scoreboard.
In reply to cgales:
Because am made connections of driver to scoreboard and monitor to scoreboard in environment only. that’s why am creating agent components in environment also …
we cannot connect components without create right.
In reply to Prawin kumar:
The agent will create its own driver, monitor and sequencer. There is no need to create them in the environment. The agent should also have an analysis port, which is connected to the monitor’s analysis port. You will connect the agent’s analysis port to the scoreboard.
A poorly written agent won’t have an analysis port, in which case you will connect the monitor’s analysis port to the scoreboard.
In reply to Prawin kumar:
Hi,
What is verbosity of UVM_INFO in uvm monitor.
i.e deference between UVM_LOW,UVM_HIGH,UVM_NONE,UVM_MEDIUM.
Thanks,
In reply to Prawin kumar:
This is what the Refernce Manual says:
Defines standard verbosity levels for reports.
UVM_NONE Report is always printed. Verbosity level setting can not disable it.
UVM_LOW Report is issued if configured verbosity is set to UVM_LOW or above.
UVM_MEDIUM Report is issued if configured verbosity is set to UVM_MEDIUM or above.
UVM_HIGH Report is issued if configured verbosity is set to UVM_HIGH or above.
UVM_FULL Report is issued if configured verbosity is set to UVM_FULL or above.
You should learn fo work with this Refermce Manual and the UVM Cookbook.
In reply to Prawin kumar:
This comes with the UVM Class Library
http://www.accellera.org/downloads/standards/uvm
In reply to chr_sue:
Tq Mr chr_sue,
Can you help on this,
I want write a uvm code for simple logic gate, with inputs of int-a,int_b output is out,
i want to randomize inputs for generation output with uvm components only,
so, i’m unable to randomize those inputs can you check it ones
**http://www.edaplayground.com/x/ttv**
Thanks,
In reply to Prawin kumar:
I can see you code, but it is not really simulating. It proceeds only in time but does not issue any uvm_info with the exception of the build_phase.
Lookin to your code I see strange things in your sequence:
start_item(req);
assert (req.randomize());
req.delay = $urandom_range(1, 20);
req.int_a = $urandom();
req.int_b =$urandom();
finish_item(req);
You are randomizing twice. First with the randomize meothod belonging to the classes, which is fine and then randomizing with $urandom, which is not good.
In reply to Prawin kumar:
I had a deeper look to your code. You do not understand the UVM build process using the different phases: build_phase, connect_phase.
Passing the virtual interface through your environment is a nightmare. TLM components never have a virtual interface!
Watch the UVM related videos in the Verification Academy, then clean-up and run your code.
In reply to chr_sue:
Can you elaborate which is mistake, build phase is very clear and connect phase also
In reply to Prawin kumar:
Your DUT is instantiated, but not connected to the interface.
I did not check all Details. My guess is yout testbench is stucking somewhere in the monitor or the scoreboard.
In reply to chr_sue:
I had a closer look to your code. The clock generation did im module top did not work.
I have fixed this. See
In reply to chr_sue:
ok chr_sue,
Thank you so much for your support.
We generates the stimulus fine but
with this i want verify the DUT? how can i?
In reply to Prawin kumar:
First you have to connect your DUT to the interface in your toplevel module. Then your Environment is complete.
To verify your design you Need sequences and Tests. In your tests you select a certain sequence to verify the features of your design.